How to Mix a Hydroponic Nutrient Solution, Step by Step

The mixing order that prevents precipitation, how to make a stock concentrate, and the exact rates per gallon for every EC target.

HGV Technical TeamUpdated November 20264 min read

To mix a hydroponic nutrient solution, start with the full volume of water, add the calcium part and let it dissolve, add the grow or bloom part, then check EC and adjust pH last. Never combine concentrated parts with each other. They only meet safely once each is diluted in the reservoir.

The one rule that prevents most mixing problems

Calcium reacts with phosphates and sulfates when both are concentrated. The result is a white solid that settles in the tank, clogs emitters and takes nutrition out of the feed. Every other step in this guide exists to keep that reaction from happening: water first, one part at a time, and time to dissolve in between.

How do you mix a batch tank, step by step?

  1. Add water. Fill the tank to its final volume before any nutrient goes in.
  2. Add Base. Add HGV Base, the calcium and nitrogen part, and let it mix for five minutes.
  3. Add Grow or Flower. Add the second part and let it mix for another five minutes.
  4. Check EC. HGV mixes to a target EC of 3.0. If you are off target, correct the dose before touching pH.
  5. Adjust pH. Bring the solution to 5.6 to 5.8 once everything is dissolved.
  6. Verify at the point of delivery. Read EC and pH where the feed reaches the plant, not only in the tank.

How much nutrient per gallon?

These are HGV's published rates for the Liquid line and for a dry concentrate mixed at 2.5 lb per gallon, in milliliters per gallon of water. Grow and Flower use the same rate.

Target ECBaseGrow or Flower
1.06 mL10 mL
1.510 mL16 mL
2.012 mL19 mL
2.516 mL26 mL
3.018 mL30 mL
3.522 mL36 mL
4.025 mL42 mL

Measuring dry product straight into a reservoir instead? At EC 3.0 the rate is 4.2 g of Base and 7.0 g of Grow or Flower per gallon. The complete tables, including 1 and 2 lb per gallon concentrates, are in the mixing and application guide.

How do you make a stock concentrate from dry nutrients?

  1. Fill the stock tank to about 70 percent of its final volume. Warm or hot water dissolves salts faster.
  2. While agitating, add the full weight of one product. A 25 lb bag in 10 gallons gives the standard 2.5 lb per gallon.
  3. Top off to the final volume and keep agitating until the solution is uniform and clear.
  4. Repeat in a separate tank for each product. Base never shares a concentrate tank with Grow or Flower.

Once a concentrate is fully dissolved it does not need further agitation or aeration. Acceptable mix rates run from 0.5 to 2.5 lb per gallon. Colder water holds less, so reduce the concentration if you cannot use warm water.

How do you set up an injector?

An injector ratio is simply dilution. At 1:100, one gallon of stock feeds 100 gallons of water. To find the ratio that delivers a given rate, divide 3,785 mL (one gallon) by the milliliters per gallon you need. A rate of 30 mL per gallon works out to about 1:126, and 18 mL per gallon to about 1:210. Set the injector, then confirm with an EC reading at the emitter and fine-tune from there.

Keep the suction strainer suspended at least 4 inches above the bottom of the stock tank so it never draws settled particles.

Where do pH adjusters and additives go?

Position in the sequence matters more than most growers expect:

  • pH Up and pH Down go in last, after EC is on target.
  • Potassium silicate goes in first. HGV Level must be added or injected before Base, because silicate binds with calcium that is already in solution.
  • HGV Clear goes into clean water first, or last when you are running Level.

The reservoir pH guide covers the full order of operations and what to do when pH will not hold.

What if the EC is off after mixing?

Use HGV's adjustment formula. Divide the EC you measured by the EC you wanted, then divide your current rate by that number. If a batch reads 2.5 against a 3.0 target, 2.5 divided by 3.0 is 0.833. A Base rate of 15 mL becomes 18 mL, and a Grow or Flower rate of 25 mL becomes 30 mL.

Frequently asked questions

Which hydroponic nutrient do you add first?

Water first, then the calcium part. With HGV that means Base, followed by Grow or Flower, with pH adjustment last. If you use a potassium silicate product such as Level, it goes in before Base.

Can I mix Base and Grow or Flower together in one concentrate?

No. Calcium in Base will react with the phosphates and sulfates in Grow and Flower at stock strength. Keep each product in its own concentrate tank and combine them only in the diluted feed.

Should I adjust pH before or after adding nutrients?

After. Every nutrient shifts pH as it dissolves, so a pH set in plain water will not survive mixing. Adjust once EC is on target.

How long does mixed concentrate last?

HGV dry fertilizers do not expire. Mixed concentrates can last several months with clean water and clean tanks, but the practical recommendation is to mix one to two months of supply, then clean the tank and start fresh.

Does hot water damage nutrients?

No. Warm or hot water speeds up dissolving and raises how much salt the water can hold. Let a concentrate cool before use if temperature matters for your dosing equipment.

Build your feed program with HGV

A two-part system that mixes to a target EC of 3.0 and a pH of 5.6 to 5.8. See the full line or talk to a rep about your room.